I am attempting to modify an original set of code which uses a spline interpolator to plot a curve representing cumulative emissions (and its derivative annual emissions). The goal is to read in the historical emissions (from histem.txt) and then track the cumulative emissions (read integral of annual emissions) which I will tack onto the cumulative emissions spit out by the spline interpolator in cumemC.txt.
program sat_profile ! This program can be used to create a smooth temperature profile starting from ! a specified slope at the year 2005 and stabilizing (with zero slope) at 2300. ! The starting slope can be calculated from the last 10 years of the simulation ! providing the initial condition at 2005. A starting temperature and final ! temperature also need to be specified. The final target temperature should be ! the modelled preindustrial temperature plus the temperature target (1.5, 2, 3, ! and 4 degrees C). An arbitrary mid point year and temperature (between 2005 ! and 2300) is also specified. This may need some adjustment in order to ! generate a smoothly changing profile without overshoot. The output is a text ! file with annual values from 2005 to 2500. This can be adjusted to provide ! interpolated values at other time intervals by changing the loop that ! generates tval and calculates yval. implicit none integer, parameter :: nd=3, iyr=2008, fyr = 2500 integer i, j real t(nd), y(nd), ypp(nd), tval, yval, ypval, yppval, ybcbeg, ybcend, offset, initg real year(257), emissions(257), HIST, TIM, sum, cem(257) real AEMIT(iyr:fyr), EMIT(iyr:fyr), TIME(iyr:fyr) ! input parameters: NOTE --> t(1) and t(3) MUST match iyr and fyr respectively t(1) = 2008. ! starting year of synthetic profile t(3) = 2500. ! year of zero emissions t(2) = 2400. ! year of peak emissions (may be adjusted) y(1) = 346.758 ! emissions at starting year (set to year 2008) y(3) = 2000 ! emissions at end (set to PI + target) y(2) = 1900 ! emissions at peak (may be adjusted) ! starting slope can be derived from the last 10 years of a simulation to 2008 initg = 8.749 ! value of EMIT(t=1) (should be the same as 2008 annual emissions in historical curve) ybcbeg = 8.749 ! slope at t(1) (Gt year-1) ybcend = 0. ! slope at t(3) (zero) offset = 0 ! time offset (half of the averaging period) ! calculate the spline derivatives call spline_cubic_set ( nd, t, y, 1, ybcbeg, 1, ybcend, ypp ) if (t(3).lt.t(2)) then print *, 'error, t(2) must be smaller than t(3)' call exit(1) endif if (t(3).eq.t(2)) then print *, 'error, t(2) must be smaller than t(3)' call exit(1) endif if (iyr.ne.t(1)) then print *, 'error, iyr and t(1) do not match' call exit(1) endif if (fyr.ne.t(3)) then print *, 'error, fyr and t(3) do not match' call exit(1) endif open(unit=15, file='histem.txt') read(15,*,end=258) year, emissions 258 open (10, file='cumemC.txt') ! evaluate the spline at points tval !change 2005, 2500 to values of t(1) and t(3) do i=1,257 sum=0 do j=1,i sum = sum + emissions(j) write (*, '(2f12.4)') enddo cem(i) = sum write (10, '(2f12.4)') year(i), cem(i) enddo do i=iyr,fyr tval = float(i) call spline_cubic_val ( nd, t, y, ypp, tval, yval, ypval, yppval ) ! if not doing stabilization, get rid of this line: !if (tval > t(3)) yval = y(3) if (tval.eq.t(1)) yval = y(1) write (*, '(2f12.4)' ) tval+offset, yval write (10, '(2f12.4)' ) tval+offset, yval AEMIT(i) = yval TIME(i) = tval end do close (10) open(10, file='anemC.txt') write (10, '(2f12.4)') year, emissions EMIT(iyr) = initg write (*, '(2f12.4)' ) TIME(iyr), EMIT(iyr) write (10, '(2f12.4)' ) TIME(iyr), EMIT(iyr) do i=iyr+1,fyr EMIT(i) = AEMIT(i) - AEMIT(i-1) write (*, '(2f12.4)' ) TIME(i), EMIT(i) write (10, '(2f12.4)' ) TIME(i), EMIT(i) end do close (10) end
also see combined.txt and histem.txt
The way I am currently reading in year and emissions via:
read(15,*,end=258) year, emissions
is storing these each as a 1-column vector. Since I need to be tracking a running sum of emissions, what I really need to be doing is storing these as 257 scalar values instead (or so I believe?). However, I am uncertain of how to do this. I have attempted using a do loop in earlier versions of the code, but was unsuccessful.
I am using a do loop for purposes of a running sum of emissions:
do i=1,257
abc=0
do j=1,i
abc = abc + emissions(j)
write (*, '(2f12.4)')
enddo
cem(i) = abc
write (10, '(2f12.4)') year(i), cem(i)
enddo
here abc represents the variable I use to keep track of the running sum, emissions are the annual emissions in GtC, and cem(i) represents the integral of emissions.
Unfortunately, because of the way this file is being read, cem(i) and year(i) do not get stored properly, and the resulting text file is erroneous.
I have attached the histem.txt file and the code (combined.txt)